Technical Data
Appearance & Odor: Amber liquid, mild odor.
Physical State: Liquid
Vapor Pressure (mmHg): N/A
Vapor Density (air=1): N/A
Boiling Point: 212° F
Freezing/Melting Point: N/A Specific Gravity (Water =1): 1.117
Evaporation Rate: Slower than ether
Solubility in Water: Complete
Preparation
Test and protect adjacent and surrounding surfaces from exposure to the
cleaning solution. Avoid direct contact with foliage. Cover landscaping
using plastic or wet the foliage with water before and after the
cleaning process.
Surfaces & Air Temperatures
Excessively high or low temperatures will produce poor results. Best
cleaning results are obtained when air and masonry surface temperatures
are 40° F or above. Do not clean when temperatures are below freezing
or will be overnight. If freezing conditions exist, allow adequate time
for masonry to thaw. If air temperatures exceed 90° F, flash cool the
surface with water before applying detergent. Do not allow product to
dry on a hot surface.
Pre-Testing
Always test in an inconspicuous area prior to beginning full scale
cleaning operations. Test cleaning effectiveness on each type of
surface and stain.
Dilutions
Use
SafeRestore undiluted for most applications. Note: Dilution of the
product maybe used based on test results, application, and the severity
of the staining.
Application Instructions
Before applying read: Preparation section and “Precautionary Measures” under Safety Information.
Recommended application is by low-pressure sprayer. Brushing is not
necessary. One single undiluted application will remove many stains.
For deep stain removal and porous surfaces, pre-wet the surface with
water. Then use a double undiluted application, spaced several minutes
apart without rinsing in between the applications. Follow with a
pressure wash rinse of approximately 1,000 psi to 3,000 psi for the
best results. Use lower rinse pressures when cleaning sensitive
substrates. Extended dwell time is very important when using this safe
product. Do not allow product to dry on the surface always rinse
thoroughly.
Coverage Rates
Coverage rates vary from 75 – 250 sq.ft./gal depending on the surface porosity, texture and severity of staining.
Suitable Substrates
Brick,
limestone, sandstone, concrete, precast, exposed aggregate, granite,
unpolished marble, synthetic stone, terrazzo, anodized aluminum, EIFS,
uncoated stainless steel, stucco, roofs, glass and virtually any type
of construction materials. Always test product in a small area
first before beginning entire project.
Stain Removal
Vanadium and manganese; any metal or mineral oxide stains; pollution
stains, concrete leaching, caulk bleed, water hardness stains and
sealer overspray from glass; and sealants.
Safety Information
Precautionary Measures: Always wear goggles and rubber gloves when
handling this product. Do not get in eyes, on skin, or clothing. If
material comes in contact with clothing, wash before reuse. Contains
Hydrochloric Acid. Avoid breathing fumes. Use adequate ventilation.
Though the potential for fuming of SafeRestore is minimal, take
precautions to avoid exposing building occupants to fumes above
permissible exposure limits (PEL) for product. Keep container closed
after handling. Applicators should wear rain suit of plastic, rubber,
or PVC boots and gloves, face shields, and goggles to avoid splash to
bare skin or eyes. Avoid drifting of material or rinse water onto autos
and pedestrians by protecting or diverting such traffic. Do not dilute
SafeRestore with any product except water. Do not use for any other
applications other than specified. Dispose of any empty containers
according to federal, state, and local requirements. Do not remove
label. Read Material Safety Data Sheet for additional safety and health
hazard information prior to use.
First Aid +
Instructions in Case of Contact or Exposure
Eyes: Flood with water 15 minutes and seek medical attention. Remove contact lenses immediately.
Skin: Wash off with soap and water, use good skin emollient. If irritation develops, seek medical attention.
Ingestion: Drink lots of water to dilute. Seek immediate medical attention. Do not induce vomiting.
Inhalation: Remove to fresh air. Call physician and seek medical attention if irritation develops.
Spill or Leak Procedures
Waste
Disposal Method: Check state, local, or federal regulations for your
area. Check for adequate ventilation to maintain PEL. Steps to be taken
if material is released or spilled: Large spill: Dike and contain for
intended use. Small spill: Soak up with an absorbent and place in
approved container for disposal.
Container Handling & Storage
Store away from all other chemicals and potential sources of
contamination. Keep container tightly closed when not in use. Wash
thoroughly after handling. Store in a cool dry place, away from alkalis.
Notice
This product has been classified in accordance with the hazard criteria of the CFR.
|
