BuddingCo.com

-Deep cleans virtually all surfaces including painted metal,
EIFS, vinyl, awnings, roofs, porous concrete, fiberglass,
siding, and wood.
-Neutralizer of choice for acids used in high rise restoration
prior to rinsing to create a neutral overspray

• • Limitations
  • * Does not remove deep black stains (use Britenol)
  • * Polished aluminum could be whitened or browned (use
  • Britenol)
  • * Works equally well hot or cold temperatures but should
  • not exceed 120 Fahrenheit.
  • Technical Data
  • Appearance & Odor: Amber color, mild citrus odor.
  • Physical State: Liquid.
  • pH: 13.5
  • Vapor Pressure (mmHg): As water
  • Vapor Density (air=1): As water
  • Boiling Point: 212° F
  • Freezing/Melting Point: N.A.
  • Specific Gravity (water =1): 1.12
  • Evaporation Rate: As water
  • Solubility in Water: Complete
  • Surface & Air Temperatures
  • Excessively high or low temperatures will produce poor
  • results and possible harm. Best cleaning results are obtained
  • when air and surface temperatures are 40° F or above. Do
  • not clean when temperatures are below freezing or will be
  • overnight. If freezing conditions exist, allow adequate time
  • for surface to thaw. If air temperatures exceed 90° F, flash
  • cool the surface with water before applying product. Do not
  • allow product to dry on a hot surface.
  • Preparation
  • Protect adjacent and surrounding surfaces not intended to be
  • cleaned when necessary.
  • Pre-Testing
  • Always test prior to beginning full-scale cleaning operations.
  • Testing should confirm cleaning effectiveness on each type of
  • surface and stain designated to be cleaned. Test also to determine
  • the desired surface contact time and any potential for
  • adverse reactions with adjacent materials. Allow test panels to
  • dry thoroughly before evaluating final appearance and results.
  • Dilu tion
  • First cut at 4:1 to make product ready to use then follow the
  • dilution range listed below. Apply using pressure washer up or
  • downstream, or low pressure spray applicator.
  • - 10:1 for difficult cleaning
  • - 20:1 for light soil
  • - Undiluted for gutters and down spouts
  • Note: Dilutions will vary based on the severity of the stain and
  • type of surface.
  • Suitable Substrates
  • EIFS, glass, painted siding, vinyl siding, gutters, downspouts,
  • masonry surfaces, vinyl awnings and wood
  • Application Instructions
  • Cleansol BC was designed for use with a pressure washer by
  • professionals but can be used by the homeowners with brush
  • or low-pressure sprayer application using either hot or cold
  • water. Brushless cleaning requires the product to be laid on the
  • surface using two quick applications, which leads to complete
  • soil release most of the time. High pressure rinsing is recommended.
  • Water softeners are built into the product; water
  • pretreatment is generally not necessary. Cleansol BC does not
  • mix with bleach.
  • Coverage Rates
  • Coverage rates will vary from 100 - 250 sq. ft. per gallon
  • depending on the surface porosity, texture and severity of
  • staining.
  • Safety Information
  • Precautionary Measures: Always wear goggles and rubber
  • gloves when handling this product. Keep off of skin and clothing.
  • If material comes in contact with clothing, wash before
  • reuse.The product contains Sodium Hydroxide. Do not get in
  • eyes, on skin or clothing. Avoid breathing fumes.
  • Cleansol BC Product Specification
  • CLEANSOL BC
  • Brushless House Wash and Painted Siding Cleaner
  • container closed when not is use. Use with adequate ventilation.
  • Applicators should wear rubber boots, gloves, face
  • shields and/or goggles to avoid splash to bare skin and eyes.
  • Though the potential for fuming of Cleansol BC is minimal,
  • take precautions to avoid exposing building occupants to
  • fumes. Dispose of empty containers according to federal,
  • state and local requirements. Do not dilute Cleansol BC
  • with any product except water. Do not use for any other
  • applications other than specified. Do not remove label. Read
  • Material Safety Data Sheet for additional safety and health
  • hazard information prior to use.
  • Spill or Leak
  • Check with the state, local, or federal regulations for waste
  • disposal methods in the area. Wear proper protective equipment
  • while doing cleanup. For large spills, dike and contain
  • for intended use. For small spills, use a chemical absorbent
  • product and place in approved container for disposal.
  • Container Handl ing/Storage
  • Store the product in a cool, dry place away from acids.
  • Keep container tightly closed when not in use. Do not use
  • pressure to empty container. Wash thoroughly after handling.
  • Do not use container as dilution or rinsing vessel.
  • Empty containers retain residue and must be handled as if
  • full.
  • Instructions in Case of Contact or Exposure
  • Eyes: Flood with water for fifteen minutes. Seek immediate
  • medical attention.
  • Skin: Wash off with soap water.
  • Inhalation: Remove to fresh air. If irritation persists, call
  • physician.
  • Ingestion: Drink large amounts of water. Seek immediate
  • medical attention.
  • Notice
  • The information herein is given in good faith, but no warranty,
  • either expressed or implied, is made. Final determination of
  • the suitability of any material is the sole responsibility of the
  • user. All materials may present unknown hazards and should
  • be used with caution. Although certain hazards are described
  • herein, we cannot be sure or guarantee that these are the only
  • hazards, which exist.
  • Disclaimer
  • This product has been classified in accordance with the hazard
  • criteria of the CFR.